Garantía de entrega
Artículo: AMZ-B09PZ3VPDM
Xentec
Xentec 9005 6000K HID Xenon Bulb Bundle with 35W Standard Digital Ballast (Ultra White, Also fit 9011,9055,9145,HB3,H12)
Size:
9005 (HB3)
Color:
6000K
Detalles del producto
Disponibilidad
En stock
En stock
Peso con empaque
0.50 kg
0.50 kg
Devolución
Sí
Sí
Condición
Nuevo
Nuevo
Producto de
Amazon
Amazon
Viaja desde
USA
USA
Sobre este producto
- This product contain 2 bulbs 2 ballasts and accessories for standard installation 9005 (HB3) Bulb Specifications General Bulb type: 9005 / HB3 Base: PX29t (plastic keyed, 3 locking tabs) Application: High beam (most common), sometimes low beam or fog lights Operating voltage: 12.8V nominal (works in 12V automotive systems) Wattage (halogen OEM): 65W Current draw: ~5.1 A @ 12.8V Dimensions Overall length: ~82 mm (3.2 in) Glass length: ~32 mm (1.25 in) Glass diameter: ~8–10 mm (0.3–0.4 in) Base diameter: ~31–32 mm (1.25 in) Mounting flange thickness: ~12 mm (0.47 in) Light Output (Halogen OEM) Lumens: ~1,700–1,860 lm (new halogen bulb, varies by brand) Color temperature: ~3200K (warm white/yellowish) Rated life: ~320 hours (typical for high beam duty cycle) HID Conversion Kit Specs (common aftermarket) Wattage: 35W (standard) or 55W (high-output kits) Voltage: Requires ballast (12V in → 85V AC output to arc tube) Luminous flux: 3,000–3,800 lm (about 2× halogen brightness for 35W, up to 4,500 lm for 55W) Color temperatures available: 4300K (OEM HID white, maximum brightness) 5000K (pure white) 6000K (white with slight blue) 8000K+ (blue-purple, less usable light) Lifespan: ~2,000 hours (varies by ballast quality and heat management) Installation Guide — 9005 Xenon HID Kit 1. Preparation Tools: Screwdrivers, zip ties, gloves. Safety: Disconnect the vehicle’s battery (at least the negative terminal). Check kit contents: Two HID bulbs (9005 type), two ballasts (and igniters if separate), wiring harness/adapters, mounting brackets. 2. Install HID Bulbs Open hood, locate the stock 9005 halogen bulb socket. Twist and remove the old halogen bulb (don’t touch halogen glass — oil shortens lifespan). Insert the 9005 HID bulb into the housing, making sure it locks in properly and beam is aligned. ⚠️ Don’t touch HID bulb glass either — handle by the base. 3. Mount Ballasts Find a dry, secure location near the headlight housing (avoid heat sources like radiator/fans). Use screws, 3M tape, or supplied brackets to mount the ballast. Keep wiring short, avoid sharp bends, and use zip ties for neatness. 4. Wiring Connections Connect HID bulb → ballast output (usually 2-pin connector). Connect ballast input → stock 9005 vehicle plug. If your kit has a relay harness (recommended): Harness connects directly to battery positive and ground, with a fuse. Uses the OEM headlight plug only as a trigger signal. Ensures stable voltage, reduces flicker. 5. Testing Reconnect the battery. Switch headlights ON. HID bulb should ignite with a bluish flash, then stabilize to white (or selected color temp). If working, re-install dust covers and secure all wiring. troubshooting guide: | Problem | Likely Cause | Solution | | -------------------------------------- | ---------------------------------------------------------- | -------------------------------------------------------------------------------------------------------- | | **One side doesn’t turn on** | Loose connector, defective ballast/bulb, polarity reversed | Swap bulb/ballast side to side to isolate fault; check polarity (HID connectors sometimes aren’t keyed). | | **Both sides don’t turn on** | Blown fuse, harness not connected, relay not grounded | Check headlight fuse, ensure relay harness ground is on bare metal, test with direct 12V to ballast. | | **Flickering / intermittent shutoff** | Insufficient voltage (modern cars have CANBUS monitoring) | Add relay harness, or CANBUS decoder/capacitor (anti-flicker). | | **Bulb color mismatch** | Bulb not burned in yet, ballast inconsistency | Let both run for 20–30 hrs; replace in pairs if one ages differently. | | **Bulb won’t fit housing** | Wrong bulb size (H11 vs 9005) | Double-check kit size — 9005 has different locking tabs than 9006/HB3. | | **Dashboard error / bulb out warning** | Vehicle CANBUS system detects low resistance | Install CANBUS error canceller/decoder module inline. | | **Buzzing or radio interference** | Poorly shielded ballast | Relocate ballast away from antenna wires; use ferrite core clips on wiring. |
$136,30
60% OFF
$54,52
IMPORT EASILY
By purchasing this product you can deduct VAT with your RUT number
$136,30
60% OFF
$54,52
20% OFF adicional al pagar con Deuna
Envío gratis
Llega en 5 a 12 días hábiles
Con envío
Tienes garantia de entrega
Este producto viaja
de USA ![]()
a tus manos en
![]()
a tus manos en
Conoce más detalles
Each bundle contain 2 bulbs, 2 ballast, and installation accessories Xenon Bulb: 2 xenon bulb fits socket size and color described on the title Ballast: 35W DC digital standard size ballast Installation: pre-assembly maybe required before installation, professional installation recommended Compatibility: please check existing bulb before placing order, if not sure please check vehicle bulb reference guide, using partfinder will not guarantee fitment, 12V input required
Compra protegida
Disfruta de una experiencia de compra segura y confiable
![]()
Garantía de entrega
Con Tiendamia todas tus compras cuentan con Garantía de Entrega o devolución total de tu dinero.
Compras 100% seguras y garantizadas, para que pidas lo que sueñas y lo recibas del mundo a tu puerta.
Tarjetas de Débito y Crédito
Visa
Mastercard
American Express
Dinners
Discover
Alias
Pagos a través de PayPal
Compra procesada en dólares con dinero en cuenta o tarjetas internacionales.
PayPal
.svg)
